Existent Gum Tester LEGT- B32

Name: Existent Gum Tester LEGT- B32
Brand: Labtron.best
SKU: LEGT-B32
Rating: 4.9 (660 reviews)

Labtron LEGT-B32 is designed with unique air compressor and flowmeter to meet industrial requirements. This instrument is designed and made as per ASTM D381 Standard test method for gum content in fuels by jet evaporation.

Name

Product

Message

Captcha

Refersh

Bath type
Bath capacity
Ambient temperature
Relative humidity
Temperature controlling range
Temperature controlling accuracy
Heating type
Evaporation bath type and size	Aluminum bath φ260 × 130 mm
Constant temperature bath
Holes for testing	5 pieces
Size of holes for testing cylinder	φ51 × 70 mm
Flow rate display
Working temperature	160 ℃ ~ 165℃
Temperature controlling methods
Temperature display
Working pressure for decompression valve	0.07 MPa
Gas source
Air flow rate at jet nozzle	600 ml / s
Dimension	590 x 480 × 340 mm
Total power consumption
Heating power
Power supply	AC 220 V ± 10 %, 50 Hz; 3.5 kW

- Metal bath as the heating system
- Rapid heating speed and uniform bath temperature
- Five samples can be determined simultaneously
- Efficient and convenient
- High quality air compressor
- Automatic temperature controlling method
- Independent flow meter
- Flow rate can be manually controlled and displayed using float ball flow meter
It is widely used in petroleum, chemical, automobile and development industry. It is the best choice for aviation gasoline and automotive gasoline manufacturing, using, and researching companies for existent gum determination.
Existent Gum Tester LEGT- B32

Related Products of Existent Gum Tester

Existent Gum Tester LEGT- B30

Oil bathBath type
5000 ml ± 50 mlBath capacity
Room temperature to 35 °CAmbient temperature
≤ 85 %Relative humidity

Existent Gum Tester LEGT- B31

Aluminum block bath, φ260 × 130 mmEvaporation bath type and size
3 piecesHoles for testing
φ51 × 70 mmSize of holes for testing cylinder
Flow meterFlow rate display

Automatic Dielectric Tester

Automatic Dielectric Tester LADT-A10

2.0 kVACapacity
2 k V/ sSpeed of voltage increase
0.01Voltage inspection accuracy
< 0.1 kVBreakdown sensitivity

Low Temperature Tester

Solidifying Point Tester LLTT-A13

± 0.5 ℃Temperature controlling accuracy
New-type refrigeration compressorRefrigeration system
Two holes in one trough, and same temperatureCold trough
≤ 30 ℃Ambient temperature

Solidifying Point and Cold Filter Plugging Point Tester LLTT-A15

New-type refrigeration compressorRefrigeration system
Cold trough I: RT ~ (-51) °C, ± 1°; Cold trough II:RT ~ (-80) °C, ± 1 °CControlling temperature of cold trough
≤ 30 ℃Ambient temperature
≤ 85 %Relative humidity

Distillate Fuel Cold Filter Plugging Point Filter LLTT-A12

(-10)℃ ~ 35 ℃Ambient temperature
≤ 85 %Relative humidity
31.0 ~ 32.0 mmSample cup Inner diameter
1.0 ~ 1.5 mmSample cup Wall thickness

Constant Temperature Needle Penetration Tester

Constant Temperature Needle Penetration Tester LTNP-A10

0 to 700 taper degree (digital display table 0-70 mm)Measuring range
Timing error is less than ±0.1 sTiming device
0.01 mm Resolution
±1 cone insertion degreeNeedle insertion accuracy

Automatic Bomb Calorimeter

Automatic Bomb Calorimeter LABC-A11

IsoperibolCalorimeter type
5 to 40°CTemperature range
5 to 40 MJ/ kgMeasurement range
A. Outer barrel temperature follows room temperature change mode Or B. Outer barrel temperature constant modeOperation Mode

Automatic Bomb Calorimeter LABC-B10

IsoperibolCalorimeter type
Fully automatic oxygen filling & releasing, fully automatic bomb raising & loweringOxygen filling
250 mlBomb volume
< 8 min full test process: <10 minAnalysis time

Automatic Bomb Calorimeter LABC-A10

IsoperibolCalorimeter type
5 to 40°CTemperature range
5 to 40 MJ/ kgMeasurement range
The outer barrel temperature is constantOperation Mode

Specific Gravity Tester

Specific Gravity Tester LSGT-A10

4000 ml × 2Vessel Volume
160 WPower of Vacuum pump
3.7 kPa（27.75 mmHg）Negative power
30 WPower of shaking machine